Water Purification System LWPS-A10 is a Type I water treatment system and the feed water is RO or distilled water. It mainly consists of pretreatment system, RO system, ultrapure water system conveying unit and control system. It consists of 254 nm UV lamp to remove the bacteria in the system and 185nm UV lamp to reduce TOC. Fully automatic control over the whole process, e.g. automatic water preparation, when water tank is full, automatically stop the system and cut off the power and water. Built-in RO membrane timing automatic flush procedures, and manual RO membrane cleaning button is available.
| Water quality | One stage (Type I) |
|---|---|
| Feed water | RO water /Distilled water<hr> Water temperature: 5 ~ 40℃ |
| Conectivity | |
| Resistivity | 18.25 MΩ.cm @ 25 ℃ |
| TOC | < 5ppb |
| Bacteria | < 0.1 cfu/ml |
| Endotoxin | < 0.001 EU/ml |
| Particle | ( > 0.22μm) <1/ml |
| Absorbance | (254nm,1cm optical distance) < 0.001 EU/ml |
| Reactive Silica(SiO2) | < 0.01 ppm |
| RNases | < 0.01 ng/ml |
| DNases | < 4 pg/μl |
| Temperature | 5 ℃ ~ 40 ℃ |
| Humidity | 10 % ~ 80 % |
| Water production rate | Type 1 water flow rate: 1-1.5 L/min |
| Micro filtration | Millipore Millipak 0.22μm membrane or hollowed fiber membrane filter |
| Power supply | 230 V/50 Hz 150 W |
| Main body Dimension (L × W × H) | 340 × 550 × 530 mm (bench type) |
Used for Medical device injection to human body, DNA/RHA preparation, DNA testing, HPLC (test and analysis of amino acid, penicillin; Organic ingredients), GCMS, ICP, IC, gas chromatography, AAS etc.
| Output 2nd stage RO water | 90 liters/hour |
| Output ultrapure water | Up to 2 liters/minute (when tank is full) |
| Ultrapure Water Quality | Resistivity (25°C) 18.2 M Ω cm<br/> TOC: < 3ppb<br/> Bacteria: <0.1 cfu/ml<br/> Particle (>0.2 µm): <1/ml<br/> Endotoxin: <0.001EU/ml<br/> RNases: <1pg/ml<br/> DNases: <5pg/ml |
| RO Water Quality | Conductivity 1st stage RO water: Feed water Conductivity ×5 %<br/> Conductivity 2nd stage RO water: 1 to 5 µs/cm |
| Water quality | Two stage(Type III and type I) |
| Feed water | Tap waterTDS≤400ppm<hr> Water temperature: 5-40℃<hr> Type 3 water ≥10L/h |
| Conectivity | <5 μs/cm@25℃ |
| Resistivity | 18.25 MΩ.cm @ 25 ℃ |
| Output 2nd stage RO water | 90 liters/hour |
| Output ultrapure water | Up to 2 liters/minute (when tank is full) |
| Ultrapure Water Quality | Resistivity (25°C) 18.2 M Ω cm<br/> TOC: < 3ppb<br/> Bacteria: <0.1 cfu/ml<br/> Particle (>0.2 µm): <1/ml<br/> Endotoxin: <0.001EU/ml<br/> RNases: <1pg/ml<br/> DNases: <5pg/ml |
| EDI | Resistivity >10.2 M Ω cm<br/> TOC: < 30ppb<br/> Silicone rejection rate: >99.9 % |
This water purification system is a combinational system that produces Type III water after RO and Type I water after deionization in one cycle
| Output of Pure water | ≥ 10 L / hr. |
| Water Type | Type I and Type III |
| Water Tank capacity | 30 L |
| Configuration | Benchtop |
| Output of Pure water | ≥ 30 L / hr. |
| Water Type | Type I and Type III |
| Water Tank capacity | 30 L |
| Configuration | Benchtop |
| Output of Pure water | ≥ 20 L / hr. |
| Water Type | Type I and Type III |
| Water Tank capacity | 30 L |
| Configuration | Benchtop |
| Water quality | Two stage(Type III and type I) |
| Feed water | Tap waterTDS≤400ppm<hr> Water temperature: 5-40℃<hr> Type 3 water ≥10L/h |
| Conectivity | <5 μs/cm@25℃ |
| Resistivity | 18.25 MΩ.cm @ 25 ℃ |
| Output 2nd stage RO water | 90 liters/hour |
| Output ultrapure water | Up to 2 liters/minute (when tank is full) |
| Ultrapure Water Quality | Resistivity (25°C) 18.2 M Ω cm<br/> TOC: < 3ppb<br/> Bacteria: <0.1 cfu/ml<br/> Particle (>0.2 µm): <1/ml<br/> Endotoxin: <0.001EU/ml<br/> RNases: <1pg/ml<br/> DNases: <5pg/ml |
| RO Water Quality | Conductivity 1st stage RO water: Feed water Conductivity ×5 %<br/> Conductivity 2nd stage RO water: 1 to 5 µs/cm |
| Water quality | One stage (Type I) |
| Feed water | RO water /Distilled water<hr> Water temperature: 5 ~ 40℃ |
| Resistivity | 18.25 MΩ.cm @ 25 ℃ |
| TOC | < 5ppb |
Radio Frequency Identification Water Purifier are equipped with a RFID Radio Frequency Identification Chip which helps keeping a check on the quality of water in real time. This helps in monitoring of parameters for the purifier
| Output of Pure water | ≥ 30 L / hr. |
| Process | Double Pass RO system |
| Configuration | Benchtop |
| Water Tank capacity | 30 L |
| Output of Pure water | ≥ 10 L / hr. |
| Process | Double Pass RO system |
| Configuration | Benchtop |
| Water Tank capacity | 30 L |
| Output of Pure water | ≥ 20 L / hr. |
| Process | Double Pass RO system |
| Configuration | Benchtop |
| Water Tank capacity | 30 L |
| Output | 30 liters/hour |
| Flow rate | Up to 2 liters/minute (with pressure tank) |
| Pure water outlet | 2 reverse osmosis water, deionized water |
| Deionized Water Quality | Resistivity: 16 to 18.2 M Ω cm<br/> Bacteria: N/A<br/> Particle (>0.1 µm): N/A |
| Output | 30 liters/hour |
| Flow rate | Up to 2 liters/minute (with pressure tank) |
| Pure water outlet | 2 reverse osmosis water, deionized water |
| Deionized Water Quality | Resistivity: 16 to 18.2 M Ω cm<br/> Bacteria: N/A<br/> Particle (>0.1 µm): N/A |
It provides Type III level water which is required for chemical and physical inspection or for washing lab glassware’s
| Output of Pure water | ≥ 20 L / hr. |
| Water Type | Type III |
| Configuration | Benchtop |
| Process | Double Pass RO system |
| Output of Pure water | ≥ 30 L / hr. |
| Water Type | Type III |
| Configuration | Benchtop |
| Process | Double Pass RO system |
| Output of Pure water | ≥ 10 L / hr. |
| Water Type | Type III |
| Configuration | Benchtop |
| Process | Double Pass RO system |