Copper Strip Corrosion Tester LRCT-A13 is a international Standard ASTM D130 (Test Methods for Detection of Copper Corrosion from Petroleum Products by the Copper Strip Tarnish Test).
| Sample hole | 4 pieces |
|---|---|
| Sample quantity | 4 to 12 pieces |
| Ambient temperature | Room temperature to 35 °C |
| Temperature controlling range | Room temperature to 100°C |
| Temperature controlling accuracy | ± 1°C |
| Temperature controller | Pt100 |
| Relative humidity | ≤ 85 % |
| Timing range | 1 min to 24 hours |
| Heating power | 600 W for temperature controlling; 1000 W for auxiliary heating |
| Total power consumption | ≤ 1800 W |
| Dimensions | 580 × 460 × 760 mm |
| Power supply | AC 220 V ± 10 %, 50 Hz |
It is suitable to determine corrosiveness of aviation gasoline, jet fuels, vehicle gasoline, and natural gasoline, hydrocarbon with Reid vapor pressure lower than 124 kPa, solvent oil, diesel oil, distillate oil, lubricating oil and other petroleum products.
| Sample hole | 4 pieces |
| Speed of stirring motor | 1400 rpm |
| Speed for sample stirring | 1000 ± 50 rpm |
| Ambient temperature | Room temperature to 35°C |
| Sample hole | 4 pieces |
| Ambient temperature | Room temperature to 35°C |
| Temperature controlling range | 0 to 100°C |
| Temperature controlling accuracy | ± 1°C |
| Sample hole | 2 pieces |
| Speed of stirring motor | 1400 rpm |
| Ambient temperature | 10 to 35°C |
| Temperature controlling range | Room Temperature to 100°C |
| Measurement range | 0 to 600 penetration scale |
| Timing controller | 5 sec or 60 sec |
| Time accuracy | ± 0.1 seconds |
| Resolution | 0.01 mm |
| Penetrometer |
|
||||||||||||||||||
| Circulatory Water Bath |
|
| Measurement range | 0 to 600 penetration scale |
| Timing controller | 5 sec, 8 sec, 10 sec, 12 sec, 30 sec and 60 sec |
| Time accuracy | ± 0.1 seconds |
| Resolution | 0.01 mm |
| Cubage of bath | Ф300 × 380 mm |
| Temperature controlling range | 0 °C ~ 100 °C |
| Temperature controlling accuracy | ± 0.2 °C |
| Temperature sensor | Industrial platinum resistance, Pt100 |
| Heating power | 2 kW |
| Cooling power | 0.5 kW |
| Steam temperature | 0 to 400℃ |
| Oven temperature | 0 to 500℃ |
| Graduated flasks | 100 ml |
| Scale division of graduated flask | 1ml |
| Distillation flask | 125 ml |
| Ambient temperature | ≤ 35 °C |
| Ambient temperature | -10°C to 35°C |
| Relative humidity | ≤ 85 % |
| Thermometer | Each one for 70°C to 90°C , 100°C to120°C , and 125°C to 150°C |
| Scale division | 0.1 ℃ |
| Air flow rate | Not less than 150 L / h |
| Max. Preset time | 99 min 59 s (100 min) |
| Chamber diameter of oven | Φ22 mm |
| Heating power of oven | 1400 W × 2 |
| Sample quantity | 2 to 3 ml (it is equal to sample depth of 3 mm to 4 mm) |
| Measurement time | 60, 120, 240, 300, and 600 s at random |
| Measurement range | 7 ppm to 5 % |
| Repeatability | < 0.029 (S + 0.6) |
| Samples | 6 |
| Temperature controlling mode | Automatic digital temperature |
| Temperature controlling range | Room temperature ~ 160 °C |
| Temperature controlling accuracy | ± 0.2 °C |
| Samples | 2 |
| Oil bath cubage | 30 L |
| Angle between bomb and water surface | 30 ° |
| Speed of rotary assembly | 100 ± 5 RPM |
| Samples | 8 |
| Temperature | 100 ℃ |
| Temperature controlling accuracy | 0.1 ℃ |
| Flow meter | 3 ± 0.3 L / H oxygen |