Specific Gravity Tester LSGT-A10 determines the theoretical maximum specific gravity of bituminous mixtures in accordance to ASTM D2041 Standard Test Method for Theoretical Maximum Specific Gravity of Bituminous Mixtures (Vacuum process). Adopted with single chip machine technology to shake a loose asphalt mixture sample submerged in water. Vacuum is applied into the sample, to extract out the air bubble.
| Vessel Volume | 4000 ml × 2 |
|---|---|
| Power of Vacuum pump | 160 W |
| Negative power | 3.7 kPa（27.75 mmHg） |
| Power of shaking machine | 30 W |
| Power supply | AC(220±10%)V, 50Hz |
| Dimension | 510×520×380 mm |
| No. | Name |
| 1 | Constant temperature water bath |
Suitable for measuring theoretical specific gravity of bituminous mixtures. Can also be used for the calculation of the percent of air voids in compacted bituminous mixtures and the amount of bitumen absorbed by the aggregates.
| Ambient temperature | 10 °C ~ 40 ℃ |
| Relative humidity | ≤ 80 % |
| Ignition Mode | electron igniter / gas flame |
| Temperature range | Room Temperature ~ 300 ℃ |
| Ambient temperature | ≤ 35 °C |
| Relative humidity | ≤ 85 % |
| Temperature range | 5 °C ~ 110 °C, Each scale division is 0.5 °C; 20 °C ~ 150 °C, Each scale division is 1.0 °C; 90 °C ~ 370 °C, Each scale division is 2 °C |
| Aperture of ignition device | 0.8 mm |
| Ambient temperature | 10 °C ~ 40 °C |
| Relative humidity | ≤ 80 % |
| Measurement Range | Ambient Temperature ~ 250 °C |
| Flash Point | Lower than 104 °C , error is 2 °C; Higher than 104 °C , error is 6 °C |
| Viscosity measurement range | 10 ~ 2000000 MPa•s |
| Ambient temperature | 5 °C ~ 35 °C |
| Ambient humidity | Not more than 80 % |
| Spindles | Four spindles of No.1 ~ 4 |
| Graduated Flask | 200 ± 0.2 ml |
| Standard Water Value | 51 ± 1 s |
| Temperature Range | 0 ~ 100 °C |
| Temperature Controlling Accuracy | ± 0.2 °C |
| Graduated Flask | 200 ± 0.2 ml (50 ± 0.2 ml for bituminous materials) |
| Standard Water Value | 51 ± 1 s |
| Temperature Range | 0 ~ 100 °C |
| Ambient Temperature | 10 °C ~ 40 °C |
| Graduated Flask | 100 ml |
| Standard Water Value | 51 ± 1 s |
| Temperature Range | 0 ~ 100 °C |
| Temperature Controlling Accuracy | ± 0.1 °C |
| Measuring range | 0 to 700 taper degree (digital display table 0-70 mm) |
| Timing device | Timing error is less than ±0.1 s |
| Resolution | 0.01 mm |
| Needle insertion accuracy | ±1 cone insertion degree |
| Ambient Temperature Range | ≤ 35°C |
| Relative Humidity | ≤ 85% |
| Heating Mantle Cap Power | 1000 W × 2 |
| Sample Determination | 2 at a time |
| Ambient Temperature | 10°C to 35°C |
| Measurement Range | 0 to 100 mg |
| Resolution | 0.1 µg |
| Max. Electrolysis Speed | 40 µg /s |
| Ambient Temperature Range | ≤ 35°C |
| Relative Humidity | ≤ 85% |
| Heating Mantle Cap Power | 1000 W |
| Sample Determination | 1 at a time |