Lubricating Oil Rust Characteristics Tester LRCT-A11 is designed and made as per the International Standard ASTM D665 - IP135. (Test Methods for Rust-Preventing Characteristics of Inhibited Mineral Oil in the Presence of Water).
| Sample hole | 4 pieces |
|---|---|
| Speed of stirring motor | 1400 rpm |
| Speed for sample stirring | 1000 ± 50 rpm |
| Ambient temperature | Room temperature to 35°C |
| Temperature controlling range | 0 to 100°C |
| Temperature controlling accuracy | ± 1°C |
| Temperature controller | Pt100 |
| Relative humidity | ≤ 85 % |
| Timing range | 1 min to 24 hours |
| Heating power | 600 W for temperature controlling; 1000 W for auxiliary heating |
| Total power consumption | ≤ 1800 W |
| Dimensions | 880 × 430 × 840 mm |
| Power supply | AC 220 V ± 10%, 50Hz |
It is also suitable to determine rust-preventing characteristics of other oils, such as hydraulic pressure oil, circulation oil, as well as liquids heavier, whose gravity is greater than water.
| Sample hole | 4 pieces |
| Ambient temperature | Room temperature to 35°C |
| Temperature controlling range | 0 to 100°C |
| Temperature controlling accuracy | ± 1°C |
| Sample hole | 2 pieces |
| Speed of stirring motor | 1400 rpm |
| Ambient temperature | 10 to 35°C |
| Temperature controlling range | Room Temperature to 100°C |
| Sample hole | 4 pieces |
| Sample quantity | 4 to 12 pieces |
| Ambient temperature | Room temperature to 35 °C |
| Temperature controlling range | Room temperature to 100°C |
| Dimension | 390 x 260 x 590 mm |
| Total power consumption | ≤ 1200 W |
| Power supply | AC 220 V ± 10 %, 50 Hz |
| Heating power of water bath | 1000 W |
| Power supply | AC 220 V ± 5 % , 50Hz |
| Measurement range | 0 ~ 75 kV |
| Voltage rising rate | 3 kV ± 10 % / s |
| Distance between electrodes | 2.5 mm |
| Power supply | AC 220 V ± 10 %, 50 Hz |
| Temperature controlling range in water bath | RT ~ 90 ℃ ± 5 ℃ |
| Cooling bath temperature | (-35) ℃ ± 1 ℃ |
| Evaporation temperature | 35 ℃ ± 1 ℃ |
| Cubage of bath | Ф300 × 380 mm |
| Temperature controlling range | 0 °C ~ 100 °C |
| Temperature controlling accuracy | ± 0.2 °C |
| Temperature sensor | Industrial platinum resistance, Pt100 |
| Calorimeter type | Isoperibol |
| Oxygen filling | Fully automatic oxygen filling & releasing, fully automatic bomb raising & lowering |
| Bomb volume | 250 ml |
| Analysis time | < 8 min full test process: <10 min |
| Calorimeter type | Isoperibol |
| Temperature range | 5 to 40°C |
| Measurement range | 5 to 40 MJ/ kg |
| Operation Mode | A. Outer barrel temperature follows room temperature change mode Or B. Outer barrel temperature constant mode |
| Calorimeter type | Isoperibol |
| Temperature range | 5 to 40°C |
| Measurement range | 5 to 40 MJ/ kg |
| Operation Mode | The outer barrel temperature is constant |
| Temperature controlling accuracy | ± 0.5 ℃ |
| Refrigeration system | New-type refrigeration compressor |
| Cold trough | Two holes in one trough, and same temperature |
| Ambient temperature | ≤ 30 ℃ |
| Refrigeration system | New-type refrigeration compressor |
| Controlling temperature of cold trough | Cold trough I: RT ~ (-51) °C, ± 1°; Cold trough II:RT ~ (-80) °C, ± 1 °C |
| Ambient temperature | ≤ 30 ℃ |
| Relative humidity | ≤ 85 % |
| Ambient temperature | (-10)℃ ~ 35 ℃ |
| Relative humidity | ≤ 85 % |
| Sample cup Inner diameter | 31.0 ~ 32.0 mm |
| Sample cup Wall thickness | 1.0 ~ 1.5 mm |
| Measurement range | 0 to 600 penetration scale |
| Timing controller | 5 sec, 8 sec, 10 sec, 12 sec, 30 sec and 60 sec |
| Time accuracy | ± 0.1 seconds |
| Resolution | 0.01 mm |
| Penetrometer |
|
||||||||||||||||||
| Circulatory Water Bath |
|
| Measurement range | 0 to 600 penetration scale |
| Timing controller | 5 sec or 60 sec |
| Time accuracy | ± 0.1 seconds |
| Resolution | 0.01 mm |