Liquefied Petroleum Gas Copper Corrosion Tester LRCT-A10 is a desktop model, good pressure and corrosion resistance. This instrument is designed and made as per International Standard of Petrochemical ASTM D130 (Test Methods for Detection of Copper Corrosion from Liquefied Petroleum Gas by the Copper Strip Tarnish Test).
| Sample hole | 2 pieces |
|---|---|
| Speed of stirring motor | 1400 rpm |
| Ambient temperature | 10 to 35°C |
| Temperature controlling range | Room Temperature to 100°C |
| Temperature controlling accuracy | ± 0.5°C |
| Temperature controller | Pt100 |
| Relative humidity | ≤ 85 % |
| Delay time | 0.01 s to 99 hours 99 minutes |
| Heating power | 600 W for temperature controlling; 1000 W for auxiliary heating |
| Total power consumption | ≤ 1700 W |
| Dimensions | 580 × 520 × 810 mm |
| Power supply | AC 220 V ± 10 %, 50 Hz |
It is suitable to determine corrosiveness of liquefied petroleum gas to copper strip.
| Sample hole | 4 pieces |
| Sample quantity | 4 to 12 pieces |
| Ambient temperature | Room temperature to 35 °C |
| Temperature controlling range | Room temperature to 100°C |
| Sample hole | 4 pieces |
| Ambient temperature | Room temperature to 35°C |
| Temperature controlling range | 0 to 100°C |
| Temperature controlling accuracy | ± 1°C |
| Sample hole | 4 pieces |
| Speed of stirring motor | 1400 rpm |
| Speed for sample stirring | 1000 ± 50 rpm |
| Ambient temperature | Room temperature to 35°C |
| Viscosity measurement range | 10 ~ 2000000 MPa•s |
| Ambient temperature | 5 °C ~ 35 °C |
| Ambient humidity | Not more than 80 % |
| Spindles | Four spindles of No.1 ~ 4 |
| Evaporation bath type and size | Aluminum block bath, φ260 × 130 mm |
| Holes for testing | 3 pieces |
| Size of holes for testing cylinder | φ51 × 70 mm |
| Flow rate display | Flow meter |
| Bath type | Oil bath |
| Bath capacity | 5000 ml ± 50 ml |
| Ambient temperature | Room temperature to 35 °C |
| Relative humidity | ≤ 85 % |
| Evaporation bath type and size | Aluminum bath φ260 × 130 mm |
| Holes for testing | 5 pieces |
| Size of holes for testing cylinder | φ51 × 70 mm |
| Working temperature | 160 ℃ ~ 165℃ |
| Calorimeter type | Isoperibol |
| Temperature range | 5 to 40°C |
| Measurement range | 5 to 40 MJ/ kg |
| Operation Mode | A. Outer barrel temperature follows room temperature change mode Or B. Outer barrel temperature constant mode |
| Calorimeter type | Isoperibol |
| Temperature range | 5 to 40°C |
| Measurement range | 5 to 40 MJ/ kg |
| Operation Mode | The outer barrel temperature is constant |
| Calorimeter type | Isoperibol |
| Oxygen filling | Fully automatic oxygen filling & releasing, fully automatic bomb raising & lowering |
| Bomb volume | 250 ml |
| Analysis time | < 8 min full test process: <10 min |
| Vessel Volume | 4000 ml × 2 |
| Power of Vacuum pump | 160 W |
| Negative power | 3.7 kPa（27.75 mmHg） |
| Power of shaking machine | 30 W |
| Test bomb | Two samples or a group of parallel samples |
| Bath temperature | 37.8 °C |
| Temperature controlling accuracy | 0.1 °C |
| Dimensions | 500 × 560 × 680 mm, 950 × 540 × 720 mm |
| Operation temperature of water bath | RT ~ 90 °C |
| Temperature controlling accuracy | ± 0.1 °C |
| Dimensions | 550 × 520 × 102 mm |
| Pressure meter accuracy | ± 0.4 % kPa |