Labtron LEGT- B30 is manufactured and made as per ASTM D381-12 “Test Methods for Existent Gum in Engine Fuels”. It is suitable to determine the tendency of fuels (gasoline, coal oil, diesel oil) to form gum when used in the motor.
| Bath type | Oil bath |
|---|---|
| Bath capacity | 5000 ml ± 50 ml |
| Ambient temperature | Room temperature to 35 °C |
| Relative humidity | ≤ 85 % |
| Temperature controlling range | RT to 250 °C |
| Temperature controlling accuracy | 150 °C ± 3 °C；180 °C ± 3 °C；250 °C ± 5 °C |
| Heating type | Electric heater |
| Evaporation bath type and size | |
| Constant temperature bath | |
| Holes for testing | |
| Size of holes for testing cylinder | |
| Flow rate display | |
| Working temperature | |
| Temperature controlling methods | |
| Temperature display | |
| Working pressure for decompression valve | |
| Gas source | |
| Air flow rate at jet nozzle | |
| Dimension | 840 x 380 x 600 mm |
| Total power consumption | ≤ 1200 W |
| Heating power | 1000 W |
| Power supply | AC 220 V ± 10 %, 50 Hz |
It is widely used in petroleum, chemical, automobile and development industries. It is also suitable for determining tendency of fuels (gasoline, kerosene and diesel oil) to form gum when the fuels are used in the engine.
| Evaporation bath type and size | Aluminum block bath, φ260 × 130 mm |
| Holes for testing | 3 pieces |
| Size of holes for testing cylinder | φ51 × 70 mm |
| Flow rate display | Flow meter |
| Evaporation bath type and size | Aluminum bath φ260 × 130 mm |
| Holes for testing | 5 pieces |
| Size of holes for testing cylinder | φ51 × 70 mm |
| Working temperature | 160 ℃ ~ 165℃ |
| Test bomb | Two samples or a group of parallel samples |
| Bath temperature | 37.8 °C |
| Temperature controlling accuracy | 0.1 °C |
| Dimensions | 500 × 560 × 680 mm, 950 × 540 × 720 mm |
| Operation temperature of water bath | RT ~ 90 °C |
| Temperature controlling accuracy | ± 0.1 °C |
| Dimensions | 550 × 520 × 102 mm |
| Pressure meter accuracy | ± 0.4 % kPa |
| Ambient temperature | 10 °C ~ 40 ℃ |
| Relative humidity | ≤ 80 % |
| Ignition Mode | electron igniter / gas flame |
| Temperature range | Room Temperature ~ 300 ℃ |
| Ambient temperature | 10 °C ~ 40 °C |
| Relative humidity | ≤ 80 % |
| Measurement Range | Ambient Temperature ~ 250 °C |
| Flash Point | Lower than 104 °C , error is 2 °C; Higher than 104 °C , error is 6 °C |
| Ambient temperature | ≤ 35 °C |
| Relative humidity | ≤ 85 % |
| Temperature range | 5 °C ~ 110 °C, Each scale division is 0.5 °C; 20 °C ~ 150 °C, Each scale division is 1.0 °C; 90 °C ~ 370 °C, Each scale division is 2 °C |
| Aperture of ignition device | 0.8 mm |
| Ambient temperature | (-10) °C ~ 35 °C |
| Relative humidity | ≤ 85 % |
| Capillary viscometer | 11 pieces |
| Stirring motor | 6 W, 1200 rpm |
| Ambient temperature | (-10) °C ~ 35 °C |
| Relative humidity | ≤ 85 % |
| Capillary viscometer | 7 pieces of Cannon-Fenske reserve-flow capillary viscometer tubes in a group |
| Stirring motor | 6 W, 1200 rpm |
| Ambient temperature | (-10) °C ~ 35 °C |
| Relative humidity | ≤ 85 % |
| Capillary viscometer | 11 pieces |
| Stirring motor | 6 W, 1200 rpm |
| Temperature range | Room temperature to 1000 ºC |
| Temperature resolution | 0.1 ºC |
| Temperature fluctuation | ±0.1 ºC |
| Heating rate | 1 ~ 80 ºC / min |
| Calorimeter type | Isoperibol |
| Temperature range | 5 to 40°C |
| Measurement range | 5 to 40 MJ/ kg |
| Operation Mode | A. Outer barrel temperature follows room temperature change mode Or B. Outer barrel temperature constant mode |
| Calorimeter type | Isoperibol |
| Temperature range | 5 to 40°C |
| Measurement range | 5 to 40 MJ/ kg |
| Operation Mode | The outer barrel temperature is constant |
| Calorimeter type | Isoperibol |
| Oxygen filling | Fully automatic oxygen filling & releasing, fully automatic bomb raising & lowering |
| Bomb volume | 250 ml |
| Analysis time | < 8 min full test process: <10 min |