Labtron LOFP-A10 is designed with higher precision and perfection to meet its wide range of applications. It is incorporated with advanced and reasonable temperature control features.
| Thermometer | 0 ℃ ~ 360 °C |
|---|---|
| Scale Division | 1 °C |
| Spout Aperture | |
| Ambient Temperature | ≤ 35 °C |
| Relative Humidity | ≤ 85 % |
| Temperature Measurement- Full Scale | |
| Temperature Measurement- Repeatability | |
| Temperature Measurement- Reproducibility | |
| Temperature Measurement- Resolution | |
| Test accuracy | |
| Reappearance | |
| Graduation | |
| Outer Crucible-Material | Carbon structural steel |
| Outer Crucible-Diameter Of Upper Opening | Φ100 ± 5 mm |
| Outer Crucible-Height | 50 ± 5 mm |
| Outer Crucible-Diameter Of Bottom | Φ56 ± 2 mm |
| Inner Crucible-Material | Carbon structural steel |
| Inner Crucible-Diameter Of Upper Opening | Φ64 ± 1 mm |
| Inner Crucible-Height | 47 ± 1 mm |
| Inner Crucible-Diameter Of Bottom | Φ38± 1 mm |
| Inner Crucible-Scale Line | 12mm away from the rim of upper opening and 18mm away from the rim of upper opening |
| Precision | |
| Gas Tube | Φ0.8 ~ Φ1 mm |
| Flame | 3 to 4 mm |
| Heater | Heated by an electric furnace |
| Heating Power | 1000W |
| Dimensions | 410 x 360 x 240 mm |
| Power Consumption | ≤ 1100 W |
| Power Supply | AC 220 V ± 10 %, 50Hz |
| =#REF! |
Used to determine the flash point and fire point of lubricating oil and dark petroleum products
| Ambient Temperature | 10 ℃ ~ 40 °C |
| Relative Humidity | ≤ 80 % |
| Temperature Measurement- Full Scale | Ambient temperature to 300 °C |
| Temperature Measurement- Repeatability | ≤ 8 °C |
| Ambient Temperature | 10 ℃ ~ 40 ℃ |
| Relative Humidity | ≤ 85 % |
| Temperature Measurement- Full Scale | Ambient temperature to ~ 400 ℃ |
| Temperature Measurement- Repeatability | ≤ 4 ℃ |
| Thermometer | 6 ℃ ~ 400 ℃ |
| Scale Division | 2 °C |
| Spout Aperture | 0.6 ~ 0.8 mm |
| Ambient Temperature | -10 ℃ ~ 50 ℃ |
| Ambient temperature | (-10) °C ~ 35 °C |
| Relative humidity | ≤ 85 % |
| Capillary viscometer | 7 pieces of Cannon-Fenske reserve-flow capillary viscometer tubes in a group |
| Stirring motor | 6 W, 1200 rpm |
| Ambient temperature | (-10) °C ~ 35 °C |
| Relative humidity | ≤ 85 % |
| Capillary viscometer | 11 pieces |
| Stirring motor | 6 W, 1200 rpm |
| Ambient temperature | (-10) °C ~ 35 °C |
| Relative humidity | ≤ 85 % |
| Capillary viscometer | 11 pieces |
| Stirring motor | 6 W, 1200 rpm |
| Viscosity measurement range | 10 ~ 2000000 MPa•s |
| Ambient temperature | 5 °C ~ 35 °C |
| Ambient humidity | Not more than 80 % |
| Spindles | Four spindles of No.1 ~ 4 |
| Penetrometer |
|
||||||||||||||||||
| Circulatory Water Bath |
|
| Measurement range | 0 to 600 penetration scale |
| Timing controller | 5 sec, 8 sec, 10 sec, 12 sec, 30 sec and 60 sec |
| Time accuracy | ± 0.1 seconds |
| Resolution | 0.01 mm |
| Measurement range | 0 to 600 penetration scale |
| Timing controller | 5 sec or 60 sec |
| Time accuracy | ± 0.1 seconds |
| Resolution | 0.01 mm |
| Coking furnace | Metal furnace |
| Heating mode | Electric heating |
| Test unit | 5 units |
| Temperature range | Ambient to 550°C |
| Porcelain crucible | 30 ml |
| Inner iron crucible | 75 ml |
| Outer iron crucible | 190 ml |
| Burner | Mig Burner |
| Bath type | Four holes with a furnace |
| Heating type | Electric resistance furnace |
| Temperature controlling range | 0 ~ 520 °C |
| Temperature controlling accuracy | ± 5 °C |
| Operation temperature of water bath | RT ~ 90 °C |
| Temperature controlling accuracy | ± 0.1 °C |
| Dimensions | 550 × 520 × 102 mm |
| Pressure meter accuracy | ± 0.4 % kPa |
| Test bomb | Two samples or a group of parallel samples |
| Bath temperature | 37.8 °C |
| Temperature controlling accuracy | 0.1 °C |
| Dimensions | 500 × 560 × 680 mm, 950 × 540 × 720 mm |