Automatic softening point tester LSPT-A10 is a bench top microprocessor controlled analytical unit that determines the softening point of two samples at once. Operated via touch panel it uses ball and ring apparatus for reliable detection. Designed as per Test methods of Bitumen and Bituminous Mixture for Highway Engineering and ASTM D36 Standard test method for Softening of Bitumen (Ring-and-Ball Apparatus) it is ideal for determining the softening points of petroleum asphalts, coal pitch, liquid petroleum asphalt, etc.
| Measurement range | 32 ℃ to 160 ℃ |
|---|---|
| Ambient temperature | 35 °C |
| Temperature resolution | 0.01 ℃ |
| Beaker volume | 1000 mL |
| Relative humidity | ≤85% |
| Heating power | 600 W |
| Total power consumption | ≤ 700 W |
| Power supply | AC 220V ( -5 % ~ 10 % ), 50 Hz |
Used in asphalt manufacturing companies, highway and bridge construction companies, laboratories, universities, scientific research institutes, etc.
| Graduated flask | 100 ml，50 ml |
| Conical flask | 100ml |
| Separatory funnel | 250ml |
| Ambient temperature | (-10 )°C to 35 °C |
| Ambient temperature | ≤ 35 °C |
| Relative humidity | ≤ 85 % |
| Precision of titration tube | Scale division is 0.02 ml |
| Total power consumption | ≤ 1200 W |
| Measurement range | ≥0.05 mg KOH/g |
| Potential measurement range | 0 to 1800.0 mV |
| Burette volume | 10 mL |
| Minimum titration volume | 0.001 ml |
| Penetrometer |
|
||||||||||||||||||
| Circulatory Water Bath |
|
| Measurement range | 0 to 600 penetration scale |
| Timing controller | 5 sec or 60 sec |
| Time accuracy | ± 0.1 seconds |
| Resolution | 0.01 mm |
| Measurement range | 0 to 600 penetration scale |
| Timing controller | 5 sec, 8 sec, 10 sec, 12 sec, 30 sec and 60 sec |
| Time accuracy | ± 0.1 seconds |
| Resolution | 0.01 mm |
| Evaporation bath type and size | Aluminum block bath, φ260 × 130 mm |
| Holes for testing | 3 pieces |
| Size of holes for testing cylinder | φ51 × 70 mm |
| Flow rate display | Flow meter |
| Bath type | Oil bath |
| Bath capacity | 5000 ml ± 50 ml |
| Ambient temperature | Room temperature to 35 °C |
| Relative humidity | ≤ 85 % |
| Evaporation bath type and size | Aluminum bath φ260 × 130 mm |
| Holes for testing | 5 pieces |
| Size of holes for testing cylinder | φ51 × 70 mm |
| Working temperature | 160 ℃ ~ 165℃ |
| Ambient temperature | 10 °C ~ 40 ℃ |
| Relative humidity | ≤ 80 % |
| Ignition Mode | electron igniter / gas flame |
| Temperature range | Room Temperature ~ 300 ℃ |
| Ambient temperature | 10 °C ~ 40 °C |
| Relative humidity | ≤ 80 % |
| Measurement Range | Ambient Temperature ~ 250 °C |
| Flash Point | Lower than 104 °C , error is 2 °C; Higher than 104 °C , error is 6 °C |
| Ambient temperature | ≤ 35 °C |
| Relative humidity | ≤ 85 % |
| Temperature range | 5 °C ~ 110 °C, Each scale division is 0.5 °C; 20 °C ~ 150 °C, Each scale division is 1.0 °C; 90 °C ~ 370 °C, Each scale division is 2 °C |
| Aperture of ignition device | 0.8 mm |
| Temperature range | Room temperature to 1000 ºC |
| Temperature resolution | 0.1 ºC |
| Temperature fluctuation | ±0.1 ºC |
| Heating rate | 1 ~ 80 ºC / min |