Ash Content Tester LACT-A10 is the device composed of muffle furnace, temperature controller and electric heating plate. It is small size and needs less land with special fire-resistant material and heating components. The heating time is short and it has a long lifetime. It used to determine the ash in the range 0.001 to 0.180 mass %, from distillate and petroleum products.
| Electric Muffle Furnace |
|
|---|---|
| Temperature controller |
|
| Electric heating plate |
|
Ash Content Tester is used to determine the ash in the range 0.001 to 0.180 mass %, from distillate and residual fuels, gas turbine fuels, crude oils, lubricating oils, waxes, and other petroleum products, in which any ash-forming materials present are normally considered to be undesirable impurities or contaminants.
| Calorimeter type | Isoperibol |
| Temperature range | 5 to 40°C |
| Measurement range | 5 to 40 MJ/ kg |
| Operation Mode | A. Outer barrel temperature follows room temperature change mode Or B. Outer barrel temperature constant mode |
| Calorimeter type | Isoperibol |
| Temperature range | 5 to 40°C |
| Measurement range | 5 to 40 MJ/ kg |
| Operation Mode | The outer barrel temperature is constant |
| Calorimeter type | Isoperibol |
| Oxygen filling | Fully automatic oxygen filling & releasing, fully automatic bomb raising & lowering |
| Bomb volume | 250 ml |
| Analysis time | < 8 min full test process: <10 min |
| Sample quantity | 2 to 3 ml (it is equal to sample depth of 3 mm to 4 mm) |
| Measurement time | 60, 120, 240, 300, and 600 s at random |
| Measurement range | 7 ppm to 5 % |
| Repeatability | < 0.029 (S + 0.6) |
| Air flow rate | Not less than 150 L / h |
| Max. Preset time | 99 min 59 s (100 min) |
| Chamber diameter of oven | Φ22 mm |
| Heating power of oven | 1400 W × 2 |
| Refrigeration system | New-type refrigeration compressor |
| Controlling temperature of cold trough | Cold trough I: RT ~ (-51) °C, ± 1°; Cold trough II:RT ~ (-80) °C, ± 1 °C |
| Ambient temperature | ≤ 30 ℃ |
| Relative humidity | ≤ 85 % |
| Ambient temperature | (-10)℃ ~ 35 ℃ |
| Relative humidity | ≤ 85 % |
| Sample cup Inner diameter | 31.0 ~ 32.0 mm |
| Sample cup Wall thickness | 1.0 ~ 1.5 mm |
| Temperature controlling accuracy | ± 0.5 ℃ |
| Refrigeration system | New-type refrigeration compressor |
| Cold trough | Two holes in one trough, and same temperature |
| Ambient temperature | ≤ 30 ℃ |
| Samples | 6 |
| Temperature controlling mode | Automatic digital temperature |
| Temperature controlling range | Room temperature ~ 160 °C |
| Temperature controlling accuracy | ± 0.2 °C |
| Samples | 8 |
| Temperature | 100 ℃ |
| Temperature controlling accuracy | 0.1 ℃ |
| Flow meter | 3 ± 0.3 L / H oxygen |
| Samples | 2 |
| Oil bath cubage | 30 L |
| Angle between bomb and water surface | 30 ° |
| Speed of rotary assembly | 100 ± 5 RPM |
| Evaporation bath type and size | Aluminum bath φ260 × 130 mm |
| Holes for testing | 5 pieces |
| Size of holes for testing cylinder | φ51 × 70 mm |
| Working temperature | 160 ℃ ~ 165℃ |
| Evaporation bath type and size | Aluminum block bath, φ260 × 130 mm |
| Holes for testing | 3 pieces |
| Size of holes for testing cylinder | φ51 × 70 mm |
| Flow rate display | Flow meter |
| Bath type | Oil bath |
| Bath capacity | 5000 ml ± 50 ml |
| Ambient temperature | Room temperature to 35 °C |
| Relative humidity | ≤ 85 % |