Labtron LOFP-A11 is designed with quartz tube heater which is highly efficient and cost effective and used to trace many products. It is designed and made as per ISO 2592, ASTM 92 “Test Methods for Flash and Fire Point of Petroleum Products (Cleveland Open Cup Methods)”.
| Thermometer | 6 ℃ ~ 400 ℃ |
|---|---|
| Scale Division | 2 °C |
| Spout Aperture | 0.6 ~ 0.8 mm |
| Ambient Temperature | -10 ℃ ~ 50 ℃ |
| Relative Humidity | ≤ 85 % |
| Temperature Measurement- Full Scale | |
| Temperature Measurement- Repeatability | |
| Temperature Measurement- Reproducibility | |
| Temperature Measurement- Resolution | |
| Test accuracy | |
| Reappearance | |
| Graduation | |
| Outer Crucible-Material | |
| Outer Crucible-Diameter Of Upper Opening | |
| Outer Crucible-Height | |
| Outer Crucible-Diameter Of Bottom | |
| Inner Crucible-Material | |
| Inner Crucible-Diameter Of Upper Opening | |
| Inner Crucible-Height | |
| Inner Crucible-Diameter Of Bottom | |
| Inner Crucible-Scale Line | |
| Precision | |
| Gas Tube | |
| Flame | |
| Heater | |
| Heating Power | |
| Dimensions | 480 x 400 x 300 mm |
| Power Consumption | 0 ~ 600 W |
| Power Supply | AC 220 V ± 10 %, 50 Hz |
| =#REF! |
It is suitable to determine flash point and fire point of petroleum products having a flash point higher than 79 °C, excepting fuel oils
| Thermometer | 0 ℃ ~ 360 °C |
| Scale Division | 1 °C |
| Ambient Temperature | ≤ 35 °C |
| Relative Humidity | ≤ 85 % |
| Ambient Temperature | 10 ℃ ~ 40 ℃ |
| Relative Humidity | ≤ 85 % |
| Temperature Measurement- Full Scale | Ambient temperature to ~ 400 ℃ |
| Temperature Measurement- Repeatability | ≤ 4 ℃ |
| Ambient Temperature | 10 ℃ ~ 40 °C |
| Relative Humidity | ≤ 80 % |
| Temperature Measurement- Full Scale | Ambient temperature to 300 °C |
| Temperature Measurement- Repeatability | ≤ 8 °C |
| Potential measuring range | (0 to ±1999.5) Mv |
| Intrinsic error | 0.1 % ±0.5 mV |
| Input impedance | Ri ≥1 × 1012 Ω |
| Burette capacity | 10 mL |
| Measuring range | 0 to 700 taper degree (digital display table 0-70 mm) |
| Timing device | Timing error is less than ±0.1 s |
| Resolution | 0.01 mm |
| Needle insertion accuracy | ±1 cone insertion degree |
| Power supply | AC 220 V ± 10 %, 50 Hz |
| Temperature controlling range in water bath | RT ~ 90 ℃ ± 5 ℃ |
| Cooling bath temperature | (-35) ℃ ± 1 ℃ |
| Evaporation temperature | 35 ℃ ± 1 ℃ |
| Power supply | AC 220 V ± 5 % , 50Hz |
| Measurement range | 0 ~ 75 kV |
| Voltage rising rate | 3 kV ± 10 % / s |
| Distance between electrodes | 2.5 mm |
| Dimension | 390 x 260 x 590 mm |
| Total power consumption | ≤ 1200 W |
| Power supply | AC 220 V ± 10 %, 50 Hz |
| Heating power of water bath | 1000 W |
| Ambient temperature | Room temperature to 35 °C |
| Relative humidity | ≤ 85 % |
| Temperature controlling range | Room temperature to 99.9 °C |
| Temperature controlling accuracy | ± 1 °C |
| Ambient temperature | Room temperature to 35 °C |
| Relative humidity | ≤ 85 % |
| Timing range | 1 s to 9 min 59 s |
| Temperature controlling range | Room temperature to 99.9 °C |
| Electric Muffle Furnace |
|
||||||||||||||||
| Temperature controller |
|
||||||||||||||||
| Electric heating plate |
|